If your Motorola Moto Z Play is experiencing issues with the LCD and digitizer assembly, it might be time to take it to your local repair shop for a check. While this type of repair might seem daunting at first, there are a few simple steps that you can take to make the process easier. In this article, we'll outline those steps for you!
What You'll Need
If your Motorola Moto Z Play is showing its age and you notice that the LCD and digitizer assembly are both beginning to fail, here is what you'll need to get the job done.
-LCD replacement: You will need a new LCD assembly. You can find these online or at your local electronics store. Make sure to get a compatible part number, as your old one may not work with the new Moto Z Play.
-Digitizer replacement: You will need a new digitizer assembly. Again, you can find these online or at your local electronics store. Make sure to get a compatible part number, as your old one may not work with the new Moto Z Play.
Replacement Process
Replacing the LCD and digitizer assembly on a Motorola Moto Z Play is relatively easy, though it requires some technical knowledge. The first step is to remove the battery cover and rear housing. Next, use a Phillips screwdriver to remove the six screws that secure the rear housing to the battery cover. Finally, gently pry the rear housing and battery cover to expose the LCD and digitizer assemblies.
First, remove the ribbon cable connecting it to the motherboard to replace the LCD assembly. Then use a flathead screwdriver to pry up the edge of the LCD panel connector just enough so you can pull it off. Next, disconnect the four cables connected to the motherboard: power supply cable, video output cable, speaker output cable, and touch screen cable. Finally, remove the two screws securing the LCD panel to the chassis.
First, detach all of its cables from beneath the chassis to replace the digitizer assembly. Once they're free, gently pull off the old digitizer assembly. Install a new one by aligning its connectors in their corresponding holes on the chassis and replacing screws that secure it in place. Finally, reconnect all of its
How to Replace LCD and Digitizer Assembly On Motorola Moto Z Play
If your Motorola Moto Z Play's LCD or digitizer assembly is failing, don't panic. There are plenty of simple and inexpensive ways to replace it yourself. This guide will teach you how to do it on a Moto Z Play running Android 7.0 Nougat or later.
First, ensure you have the correct toolkit and parts necessary for the repair. You'll need a Phillips screwdriver, replacement LCD and digitizer panels (which can be found online or at your local electronics store), adhesive, and a hair dryer or heat gun.
The first step is to remove the battery cover on the back of the phone. Once that's done, use a Phillips screwdriver to remove the four screws holding the battery cover. Then gently lift the body and set it aside.
Next, use the adhesive to attach one of the new LCD and digitizer panels to the phone's motherboard. Ensure that the panel is aligned correctly before securing it with the four screws removed in Step 1. Once it's connected, replace the battery cover and screws.
Now it's time to replace the LCD screen on your Motorola Moto Z Play. Start by lifting MPD mobile Parts.

How To Troubleshoot Motorola Moto Z Play LCD and Digitizer Assembly Issues
If your Motorola Moto Z Play displays inaccurate or failing images, it may be time to replace the LCD and digitizer assembly. This guide will walk you through the necessary steps to replacing the body.
If your Moto Z Play is not displaying accurate images, first make sure your device is fully charged and connected to a compatible power source. Next, turn off your device and remove the battery. Finally, remove the back cover of your Moto Z Play and locate the LCD screen and digitizer assembly.
To replace the LCD screen and digitizer assembly on your Motorola Moto Z Play, follow these steps:
1. Remove the screws that secure the screen to the frame.
2. Disconnect the cable that connects the screen to the motherboard.
3. Lift the screen and replace it with a new one. Make sure you align the new screen's pins correctly with those on the frame. Replace the screws that secure the screen to the edge.
4. Connect all cables and tighten them using a Phillips screwdriver lcd phone parts .
Conclusion
If your Motorola Moto Z Play has issues with its LCD or digitizer, this guide will help you replace the assembly. This guide is for those comfortable working with a screwdriver and a Phillips head screwdriver. If you are uncomfortable working with tools, I recommend finding an expert to repair you. Read through the steps in this article for more information on how to replace the assembly.